Electronic AC Leak Sensor (Electronic AC Leak Detector) — Split/VRF • Central AC
Winsen® electronic AC leak sensors provide continuous, fixed monitoring for air-conditioning refrigerants across residential and commercial buildings. We support A1 (R134a, R410A, R404A), A2L (R32, R454B, R1234yf/ze) and A3 (R290, R600a) gases. Choose Je n za ppm zgodnje opozarjanje oz MOS/IR-LEL for %LEL safety interlocks—ready for BMS/PLC via 4–20 mA, RS-485 Modbusin relejni izhodi.
- A1 / A2L / A3 pokritost
- NDIR ppm & MOS %LEL
- OEM/ODM • Množična naročila
- Hiter dobavni rok
Model Guide — Pick by Refrigerant Class & Measurement
A1 (R410A / R134a) — NDIR PPM
- Ranges: 0–1,000 / 0–5,000 ppm (customizable)
- Izhodi: 4–20 mA, RS-485 Modbus, 1–2 releja
- T90 ≤ 30 s • Majhen zanos, dolga življenjska doba
A2L (R32 / R454B / R1234yf/ze) — NDIR PPM / %LEL
- PPM early warning and/or 0–100% LFL/LEL
- 4–20 mA / RS-485 / releji
- VRF rooms & hotel guestrooms
A3 (R290 / R600a) — %LEL Safety
- Range: 0–100% LEL (IR-LEL or MOS)
- Relays for ventilation & shutdown interlocks
- IP options for cold/mechanical spaces
What is an Electronic AC Leak Sensor?
An electronic AC leak sensor is a fixed, continuously-monitoring detector installed near indoor units, AHUs, or mechanical rooms to measure refrigerant concentration and automatically trigger alarms in interlocks (purge fans, equipment shutdown). It complements the handheld sniffers technicians use for pinpointing leaks.
NDIR senzor hladilnega sredstva
Polprevodniški senzor hladilnega sredstva
Technology Options
| tehnologija | Najboljše za | Razpon | Prednosti | Premisleki |
|---|---|---|---|---|
| NDIR (infrardeči) | A1 ppm; A2L ppm/%LEL | ppm → %LEL | High selectivity & stability; not O₂-dependent; long life | Protect from heavy condensation/dust (filters/enclosure) |
| MOS (polprevodnik) | A2L/A3 %LEL | 0–100 % LEL | Hiter odziv; robusten; stroškovno učinkovito | Cross-sensitivities possible; periodic calibration advised |
| Katalitična kroglica | Splošni ogljikovodiki (A3) | 0–100 % LEL | Mature tech for flammables | Requires O₂; susceptible to poisons (silicones/lead) |
Tipične aplikacije
Split/VRF indoor units & hotel rooms
Mount low (~150–300 mm above floor) near indoor units and pooling points. Pre-alarm → fresh-air purge; main alarm → fan/indoor-unit shutdown.
Central AC (AHU/MAU) & mechanical rooms
Place near coils, TXVs, and floor low spots/sumps; use IP-rated housings. Integrate with BMS to start purge fans at pre-alarm and trip systems at main alarm.
Line sets, condenser/evaporator sections
Monitor around brazed joints, service valves, manifolds; avoid strong supply streams that could bypass the sensor.
Heat pumps
For A2L/A3 systems, use %LFL tiers (~25% pre-alarm; ~50% main) to trigger ventilation and safe shutdown.
Core Specifications
| Parameter | Vrednost / možnost |
|---|---|
| Merjenje | NDIR ppm and/or %LFL (MOS/IR-LEL) |
| Izhodi | 4–20 mA (2/3-žični), RS-485 Modbus RTU, 1–2 releja (N.O./N.C.) |
| Odzivni čas (T90) | ≤ 20–30 s tipično |
| Dobava | 12–24 VDC (drugi na zahtevo) |
| Pogoji delovanja | −20…+50 °C; 15–95 % RH brez kondenzacije (odvisno od modela) |
| Ohišja | Wall, panel, duct; housings up to IP65 |
| Skladnost | CE & RoHS; designed for BMS/PLC integration |
Placement & Setpoints — Good Practice
- Montažna višina: Most AC refrigerants are heavier than air ⇒ mount low; confirm with room airflow.
- Pokritost: ~5–10 m radius per sensor in open rooms; add units near valves/joints and low pockets.
- Alarmi: A2L/A3: pre-alarm ≈25% LFL; main ≈50% LFL. A1: ppm tiers (e.g., 1,000–5,000 ppm) per design spec.
- Zapore: Pre-alarm → ventilation; Main → equipment shutdown + beacons/horns/BMS event.
Dokončajte mejne vrednosti in količine glede na lokalne kode in specifikacije vašega projekta.
Zakaj nas globalne stranke izberejo?
Podjetje se dosledno drži politike kakovosti »Fine izdelave, znanstvenih inovacij, prizadevanja za odličnost in storitev z dodano vrednostjo«. Z oblikovanjem načrtov vodenja proizvodnih procesov in delovnih navodil je vzpostavil standardiziran, odgovoren in urejen sistem vodenja procesov. Poleg tega je podjetje samostojno razvilo sistem vodenja proizvodnje MES, ki omogoča celovito in vizualno upravljanje celotnega delovnega procesa.
30+ LET IZKUŠENJ
R&D, manufacture and sales of sensors and sensing solutions.
JAMSTVO ZA KAKOVOST STALNO IZBOLJŠEVANJE
Popoln in tog nadzor poteka procesa, skupaj s pomembnimi izboljšavami.
MEDNARODNI TRG
Dostavite izdelke za zaznavanje v več kot 100 držav in regij.
STABILNA DOBAVNA VERIGA ZANESLJIVA PROIZVODNJA
Osrednje komponente, za katere ne veljajo omejitve, napredna oprema za proizvodnjo in testiranje.
R&D STRENGTH TECHNOLOGY INNOVATION
200+ patents, 180+ R&D team members, self-built labs for continous innovation.
Storitev na enem mestu
Strokovno svetovanje, hitra dostava, 24-urna poprodajna podpora.
Leading the Industry, Innovative & Controllable Technology
With robust R&D capabilities, we maintain sustained input in R&D and unwavering commitment to technological innovation. This not only ensures that we remain at the forefront of industry but also drives continuous innovation, leading the future trend of the sensing industry.
Zahtevajte posvetovanje
FAQs — Freon Gas Sensors
How many sensors do I need per room?
Plan ~5–10 m radius coverage per sensor in open rooms. Add units near indoor units, valves, joints, and floor-level pockets where gas may accumulate. Irregular layouts typically need more sensors.
What alarm thresholds should I use?
For A2L/A3 gases: pre-alarm ≈25% LFL to start ventilation; main ≈50% LFL to trip equipment and trigger beacons/horns. For A1 gases, use ppm bands (e.g., 1,000–5,000 ppm) per project spec and risk assessment.
Where should the sensor be mounted?
Most AC refrigerants are heavier than air; mount low (≈150–300 mm above floor) near likely leak sources and pooling points. Avoid strong supply air that could bypass the sensor. Probe/duct versions can monitor return air.
How often should I calibrate and bump-test?
Typical calibration is every 12–24 months with periodic bump tests (quarterly/biannual). Dusty or humid sites, or areas with cleaning aerosols, may need more frequent checks and filter maintenance.
Which technology should I choose: NDIR or MOS?
Choose NDIR for ppm early warning and long-term stability; choose MOS or IR-LEL for %LEL safety interlocks on A2L/A3 systems. Many sites use both tiers for redundancy.
Can Winsen customize for OEM/volume programs?
Yes—ranges, firmware, Modbus mapping, connectors/harnesses, housings (IP rating), labels/branding, and packaging can be tailored for volume deployments.
